1. electric jack and impact wrench for car
1.1 electric jack
1.1.1 Capacity : 1000kgs, 1500kgs and
1.1.2 Working Voltage : DC13V+/- 1V
1.1.3 Max.Current : 10A
1.1.4 Max.Height: 35cm
1.1.5 Min.Height: 12 cm
1.2 impact wrench
1.2.1 Voltage: DC13+/- 1V
12.2 Max.Current: 10A
1.2.3 Max.Torque : 350 Nm
1.2.3 Size of Sleeve: 17-19mm, 21-23mm
1.3 Operation Conditions
1.3.1 Temperature : -20 + 40
1.3.2 Car Weight : below 3000kgs
1.2.3 On smooth and solid groud without strong magnet
1.4.1 Measure of Carton: 46cm* 41cm*36cm
1.4.2 Package: 3sets in a carton
1.4.2 Gross Wt/Net Wt: 23.51kgs/22kgs
2. quality with certificate iso9001 and ce certificate
3. description for usage
Please read this description carefully before usage.
3.1 Vehicles are stopped on the solid ground, can not be stopped at the gradient slope greater than 6 and to ensure the car will not move;
3.2 Launch vehicle engine, pull out the car cigarette lighter and insert the plug of the long line of the set into inside the car ignition. Look at picture 1
3.3 Take out electric jack, put it in the car underneath and close to the wheel in the formation of solid ground, insert plug of short line of the sets into the control of the jack.Look at picture 2
3.4 Hold down the up button, Jack began to rise to let jack's head close to the bottom of the car, but pay attention to the notch or flat of the Jack touching the bottom of the car or the corresponding solid ground, then continue to push up botton to rise car until tire leaves the ground up to 5 cm height.
3.5 Pull out The long-term control of the plug from the jack jack handle short-term pull out, and long-term plug into the cable jack electric wrench
3.6 Select a sleeve nut matching the vehicle, install it in the little square head of the wrench correctly.
3.7 Set the square head of the wrench into the tire nut, hold down the switch "L" side, electric wrench head start to release tire nut.
3.8 If the screws has rusted, should be added to lubricating oil in the screw.
3.9 When all the nuts on the tire are removed, the tire is replaced and and electric wrench start tightening nuts .
3.10 Set the sleeve into nuts of the tire, hold down the switch "T" to tighen tire nuts.
3.11 Upon the impact of three or four voices heard ，nuts have been tightened and stop holding down "T".
3.12 Pull out the plug of wrench and insert the plug of the jack and vehicles start from the top to down.
3.13 Press “down” button, jack began to go down till it touches ground safely and get out jack.
3.14 Put jack and wrench back to the box.
4.1 Suitable keeping temperature between 0 and 70 C
4.2 Avoid to collision, upside down and water
4.3 Add lubricate on jack before use
4.4 Clear and dry them after use
4.5 Not change any safe part
Electric car jack makes the driver to replace tires easier and more quickly.You just press the key on the control panel to lift the car, especially for the lady to replace tire when she encounter the cracked tire on the way.
Do not move the car when electric jack is working, carefully watch the working state and detail of electric jack.
1. Read the operating instructions carefully and understand the operational guidance before you use it.
2. Electric jack must be used within the scope of the application, do not overload.
3. Electric jack can not be used on soft ground but flat firm ground.
4. Keep your body away from the car when electric jack is working.
5. Electric jack is not suitable for long and continuous work.
6. In case of emergency, immediately unplug the plug of electric jack.
7. Pay attention not to pinch your fingers.
8. Electric wrench can not use continuously exceed 10 minutes.
9. When unclamp the screw cap, make sure the correct sleeve is full in the screw cap.
10. When the electric wrench is working, do not to touch the rotating parts.
11. Do not tighting the screw cap to hard when you use the electric wrench.
12. Keep the children away from the workplace.
Maintenance and repairment of tool sets should be in accordance with the instruction manual
1. Add lubricating oil to jack screw before use.
2. Make them clean and dry after use.
3. Do not replace any part affecting its safety.
Contact Name: Liu
Company Name: Jiangxi Rich Economy and Trade Co., Ltd.
Street Address: No.364, Fuzhou Road,
Nanchang, China. 330077
Member name: JIANGXIRICH
Member Since: 20 September 2010
Total Leads: 11 JIANGXIRICH Import Export Business Leads
Business focus: Ceramic Knives
Verify: Safe Import Export Tips