This product is one of popular wireless infrared detectors, compounding of macro wireless
transmitting circuit, infrared detecting system and so on.
A. Stronger anti-error report and much better detecting ability.
B. Easy to install, absolutely wireless, power supply built-in, wireless telegraph transmitting signal.
C. Save power design with high capacity, it last longer than other wireless infrared detector.
D. Extending socket built-in, compatible with wireless multi-host.
Power supply: AA, 1.5V dry battery. 2500mAH, at least continues working for two years.
Working current: static < 30µA; alarm < 20 Ma
Self-check: 1~2 minutes
Wireless parameter: frequency 315MHz, Transmitting distance >150 m (wide area without interfere) KM-2000 communication mode.
Working mode: power save mode (twice alarm minimum alternation time is about seven minute; Test mode: (twice alarm minimum alternation time is 20 second)
Sensor: Special made low noise double configuration.
Sensitive indicator: When detect people body go through the curtain defense area, the red LED turns on for 1.5 second and transmit the signal.
Lens window: 31 pcs
Detecting wide angle: 110º
Cover area: 9×9m (Typical detecting area)
Sensitivity: Jump line adjusted : (Far:9~18 m, Medium: 6~12 m, Short:4~8m, Three grades)
Batter low power: When Battery is low about 2.5 V. Greed LED turns on. Every 20 seconds (in TEST mode) or every 150 seconds(in save power mode), Red LED turns on for 1.5 seconds to send out wireless signal to receiver for alarm, but it does not execute other command.
Working condition: working temperature: -10ºC~55ºC
Stored temperature: -25ºC~65ºC
Anti-white light: >6500 LUX
3.1 Zero false alarm setting.
A) Jump line B to be set to the short position: 4~8 m, Jump line “ PULSE” to be set to position “2”
B) Do not mount two or more than two intelligent IR detectors in the same near detecting area so as to avoid two of these detectors simultaneity tough off.
C) When it is installed at the high temperature, in order to get best result, it is suggested to put the detector along the area with the lowest temperature. Do not install it under the sunshine. Detecting area is not allowed to put clothing, curtain, trunk shaking.
D) If put the detector at interferential place, it reduces the effective detecting distance.
3.2 Installing guide
The bottom cover is closed to the wall with LED side up. Stick it by double side sticker or mount it by screw. It should be mounted at 1.5 ~2.5m height and can be adjust at left, right and wide angle by selecting the stand setting.
Plug the batteries connection, than the detector self-check for two minutes and enter regular work situation.
Red LED turns on for 1.5 seconds, the detector detects body in the area, than it transmits wireless alarm signal.
Green LED turns on, Red LED runs on for 1.5 seconds. Battery power is too low, it transmits signal.
Record button: press the record button to constantly transmit wireless alarm signal so to fit the alarm host record message.
Jump line A: Connect with USE, after the detector successfully alarms once, it will stop working for 150 seconds so as to prepare for next detecting action for saving power. Connect with TEST, after the detector successfully alarms once (or action), it just delay for 20 seconds, and than it can alarm again so as to test as installation.
Jump line PULSE: Connect with “1 “, the pulse figure is one, Connect with “2 “, the pulse figure is two, ( Original jump line default set for “2” by manufacturer)
Jump line B: Sensitivity adjustment:
From 4-8 m: max sensitive distance is 4-8 m.
From 6-12 m: max sensitive distance is 6-10 m.
Contact Name: Jackie Chow
Company Name: VSTAR International Ltd.
Street Address: No.203 Building,
Shatoujiao, Yantian District,
Member name: burglaralarmsystem
Member Since: 29 July 2009
Total Leads: 1750 burglaralarmsystem Import Export Business Leads
Business focus: Burglar Alarm System, Home Security Alarm System, Wireless Alarm System, Gsm Alarm System
Verify: Safe Import Export Tips
Product Category: Motion detectors